Did you know?
ALL products we sell are factory new and come with the full Manufacturers Warranty!

Boatersland Marine > Sailing > Sailing Accessories > Forespar SR-2 Jib Roller
  Forespar SR-2 Jib Roller
Click to enlarge

Forespar SR-2 Jib Roller

Item #: FOR210003




List Price:




No restocking fees on return.
Click to verify BBB accreditation and to see a BBB report.  


SR-2 Jib Roller

The Forespar® SR-2 Jib Roller with fit shrouds from 3/16” thru 3/8” wire diameter. 

Use the proper size pair of insert liners according to the table below:

  • 3/8” wire – use no insert
  • 5/16” wire – use #1 inserts
  • 9/32” wire – use #2 inserts
  • ¼” wire – use #3 inserts
  • 7/32” wire – use #4 inserts
  • 3/16” wire – use #5 inserts

The Jib Rollers may be placed just above or below the spreader tips; however, installation will be easier if located below the spreaders. In this instance, you can pre-assemble the parts while on deck and reduce the possibility of losing parts while hanging in a boatswain’s chair. Have a 3 inch piece of masking tape within handy reach (stick it to the shroud).

Select the proper inserts, place them into the two halves of a hub and fit them around the shroud. Use the tape to loosely hold these parts together. Note that the hubs have two clearance screw holes at one end. Match these with the smaller holes at the other end of the other half. It is important that the mating faces of the inserts are parallel with the faces of the hub halves. Install the four screws supplied, tightening only to the extent that you can still slide the hub assembly up the wire shroud. Now remove the tape. 

Next, install the rollers. Note that one half of each roller has clearance holes for the two screws. Mate these halves that don’t have clearance holes. Run these screws tight. Now slide the Jib Roller to the desired position on the shroud and finish tightening the four hub screws until the hub interfaces are fully closed.

Did you Know?

ALL products we sell are factory new and come with the full Manufacturers Warranty!

Related products
Barton Marine Line Tamer - Grey - (pair) |  Barton Marine Line Tamer - White - (pair) |  Barton Marine Folding Stainless Steel Mast Step |  Barton Marine Dinghy Mast Support |  Barton Marine Carbon Tiller Extension - 700mm |  Barton Marine Carbon Tiller Extension - 1200mm |  Barton Marine Stainless Steel Rubbing Strakes - 203 X 19mm (7-7/8" X 3") |  Barton Marine Stainless Steel Rubbing Strakes - 305 X 19mm (1' X 3/4") |  Barton Marine "racer" Insert Pack |  Barton Marine Flexible Tiller Joint |  Barton Marine "cruiser" Insert Pack |  Barton Marine Light Flexible Tiller Joint |  Davis Shockles Minishockle - 12" - Black |  Davis Shockles Minishockle - 24" - Black |  Edson Stainless Replacement Brake Knob |  Edson Superlube Conduit & Bearing Lubicrant - 14OZ |  Edson Stern Rail Outboard Aluminum Motor Mount for 1-1/4" Railings |  Edson Leather Shackle Pulls |  Edson "comfort Grip" Leather Wheel Cover Kit - 32"-40" - Gray |  Edson CLAMP-ON Drink Holder - Single - White Poly |  Edson CLAMP-ON Drink Holder - Double - White Poly |  Edson Leather Spreader Boots Kit - Large |  Edson Leather Spreader Boots Kit - Small |  Edson Leather Turnbuckle Covers - Large |  Edson Leather Turnbuckle Covers - Medium |  Edson Leather Turnbuckle Covers - Small |  Forespar 27"-48" TWIST-LOCK Steering Control Arm Fits 7/8"-1" Wheels |  Forespar Big Stick 72" - Carbon - 7/8" Shaft |  Forespar Big Stick 48" - Carbon - 7/8" Shaft |  Forespar Tiller Lock Box |  Forespar WL-1 Floating Strobe LED Water Light |  Forespar ML-1 LED Spreader/Deck Light |  Forespar Mast Light Guard |  Forespar ML-2 LED Combination Deck/Steaming Light |  Forespar Nash 207 Racing Signal Flag Label |  Forespar SR-2 Jib Roller |  Forespar Railfast 324 Flag Pole Holder - 1" Base |  Forespar Railfast 324 Flag Pole Holder - 1-1/4" Base |  Forespar Lightning Master - Static Dissipater |  Davis Crazy Kids Optimist Mast Pin Set

Forespar SR-2 Jib Roller - Sailing Accessories

9:30 AM - 5:00 PM Eastern, Monday - Friday

facebook twitter